Topics

31

Support Questions / v398t - ArgumentOutOfRangeException

« on: July 21, 2015, 09:27:44 PM »

SCLMicro driver , I have a Selector switch and 2 momentary buttons , all using b3/bits ,  If i change its position 2 or 3 time i get the fist error , if I click the push button after changing the switch position I get the 2nd error

Darrell

32

Open Discussion / Driver compatabilty

« on: June 21, 2015, 11:37:50 AM »

Just out of curiosity , is there a list as to what drivers are compatible with what PLC's, There are so many plc's on the market today and myself being only familiar with Allen Bradley PLC's  and prosoft modbus cards it's a bit hard to buy something else to experiment with . If there isn't one maybe this is a good place to start one.

33

Open Discussion / change Network Adapter settings

« on: June 16, 2015, 11:39:34 PM »

Has anyone change come up with a way to change the Network Adapter settings from within AHMI as a computer may not be dedicated only for use of a HMI, and would save searching for the network adapter as Ive seen people accidentally change the wrong one an wondering why it doesn't work.

Darrell

34

Support Questions / Diable Subscriptions on a form

« on: June 11, 2015, 10:58:02 AM »

If I disable Subscriptions Should I still see messages  "could not connect to 10.100.230.101

35

Open Discussion / What Industrial monitors have you used AHMI on

« on: June 10, 2015, 06:10:01 PM »

Just a bit  curios as to what monitors or  that AHMI can be used on. Can it be run on any Allen Bradly panel views

Darrell

36

Feature Request / Keypad Read button

« on: May 09, 2015, 11:40:23 AM »

I would be nice to have a read button on the keypad , so if you are changing a value you can see what it was prior to changing it , for example changing timer preset it would be nice.

Darrell

37

Support Questions / CLX Driver

« on: May 04, 2015, 01:02:57 PM »

DigitalPanelMeter and label , when reading floating point value form CLX driver , all will flicker between some unknown value and  a good value,

have 3 panel meters reading temperatures and 2 labels reading temperature setpoints , what happens is that they will all continiously flip between ,
lets say 20 and 6.8976. All will show same value  - 398d seem to work fine, problem  the latest ver g

BevelButtonDisplay will not work now either, data type bool

Label will read timer values ok ,

Darrell

38

Support Questions / 3 position sw.

« on: May 01, 2015, 01:00:23 PM »

When I start my HMI , the switch always shows Center position , if the bit for right or left is true it still shows the Center position ,   Micrologix 1400 ,  I have to click it to show the correct position

Darrell

39

Support Questions / copying MessageDisplayByBit from another HMI

« on: April 21, 2015, 08:03:11 AM »

Is there a way to copy a MessageDisplayByBit from another HMI to a new HMI and have all the massages stay with it. I can copy a messageDisplayByValue all all the messages will be still there , but the MessageDisplayByBit I have to re-enter the messages.

Darrell

40

Support Questions / display correct temperture value from modbus registers

« on: April 06, 2015, 10:11:21 PM »

I am reading Modbus register for example 40001  and 40002 for temperature < it comes from a control logix  floating point which is 32 bit and has to be split into two  16 bits words to transmit over modbus , my question is how can I put it back together and display the correct value in a digital panel meter.

Darrell

41

Support Questions / force a new Plc Address into PlcAddressValue

« on: April 06, 2015, 10:01:27 PM »

How can I force a new plc address into PlcAddressValue , what code is needed for a button to do this.

Darrell

42

Open Discussion / JENEsys pc-1000

« on: April 04, 2015, 02:58:05 PM »

Anyone used AHMI with JENEsys PC -1000 that would like share there experience, doing some work on a couple of systems run by this and was wondering if AHMI could be used with it
.

Darrell

43

Support Questions / Message Display by bit

« on: April 02, 2015, 09:31:03 PM »

message display by bit with micrologix driver , when I build Adv HMI i get this error , using N14:6    bits 0 to 15

44

Support Questions / Control Logix - Driver

« on: March 11, 2015, 09:44:39 PM »

Since V397 D I cant seen to get this to work , Momentary buttons , in control logix , an  actual input will work but controller tags will not , bool , int , etc.  Basic Indicator same problem , In 397d all worked fine . Tried the latest version with no success ,  I could send you the actual project files if that would be any help

Darrell

45

Support Questions / DigitalPanelMeter display Decimal point

« on: February 28, 2015, 10:52:17 PM »

DigitalPanelMeter  How can I get the decimal point to display properly , if I have for example 45.1 and  put a 1 in the decimal position I now display 4.5 , If I use a floating point for a PLC address I would like to display the correct value

thank Darrell