1
Open Discussion / Re: Zombie posts
« on: June 10, 2023, 07:40:35 AM »
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Feature Request / Re: Version Labels for both AdvancedHMI Build and Current publish revision
« on: August 01, 2022, 03:13:32 PM »
As an alternative , I place a small AHMI logo at hte bottom left of the main screen with the AHMI Website address below and a label above with the date that the last change was made . I also change the properties of the mani form title to the AHMI version for example : - AHMI_V399x Turret lathe V4.7
Pal
Pal
3
Support Questions / Re: Map indirect addressed tag in my VB Solution
« on: April 25, 2022, 03:14:52 PM »
If you have an array that you are addressing there are 2 ways . 1st in the plc copy the result of the indirect address to a new tag and send that . 2nd copy the array to the hmi using the data subscriber and also the index and use VB to get the indirect tag . can't say more without plc type and more detail on what you want to achieve .
pal
pal
4
Support Questions / Re: Using the control messagelistbybit as an alarm display.
« on: January 29, 2022, 03:49:24 PM »
An alternative is to use the message list by values . I use mainly allen bradley 5000 and it has a useFul instruction - FBC . ( File Bit Compare ) . The biggest alarm array Iv'e programmed had 203 alarms and used an array of 8 32 bit words. Using a timer when an alarm is found , the display will cycle through any active alarms in the array , stopping for the timer setting at each alarm .
Regards Pal
Regards Pal
5
Open Discussion / Scamming this site ?
« on: May 16, 2018, 04:10:42 PM »
Hi ,
Just been hit with a side ad :- congratulations you are the 1,000,000 visitor (Date and current time given) . You might be chosen for an apple product by our random selection.
Click here
You have been warned
Paul
Just been hit with a side ad :- congratulations you are the 1,000,000 visitor (Date and current time given) . You might be chosen for an apple product by our random selection.
Click here
You have been warned
Paul
6
Support Questions / Re: Version 3.99 and VB 2010
« on: February 13, 2018, 06:12:29 PM »
If it helps , I am using AHMI v 3.99r with 2010 sp1 . As Godra said , non - appearing drivers was a problem suspected to be in studio . Putting any driver from the toolbox onto your form and then building has always populated the rest of the drivers into the toolbox for me . You can then insert the driver you want and delete the 1st .
Archie , for me I still have not figured out how to deploy a small enough version of VB offline . The target machine has no internet connection , nor will it for security reasons .
Paul
Archie , for me I still have not figured out how to deploy a small enough version of VB offline . The target machine has no internet connection , nor will it for security reasons .
Paul
7
Support Questions / Re: Visual Studio 2017 Community
« on: August 03, 2017, 12:19:50 PM »
Hi Archie ,
Thanks for the quick response . I will try this out and let you know how it goes .
Paul
Thanks for the quick response . I will try this out and let you know how it goes .
Paul
8
Support Questions / Visual Studio 2017 Community
« on: August 03, 2017, 11:39:59 AM »
Hi Archie ,
Do you have any idea where I can download an iso image or buy a cd of this program . Where I use AHMI there is no reliable internet connection ( slow and drops occasionally ) for large downloads .
Paul
Do you have any idea where I can download an iso image or buy a cd of this program . Where I use AHMI there is no reliable internet connection ( slow and drops occasionally ) for large downloads .
Paul
9
Support Questions / Re: Forms not communicating besides MainForm on 399r
« on: December 02, 2016, 05:36:55 PM »
Hi kay_gsr13 ,
Unfortunately I have an earlier version of rs5000 , so I was unable to open it .
Paul
Unfortunately I have an earlier version of rs5000 , so I was unable to open it .
Paul
10
Support Questions / Re: Forms not communicating besides MainForm on 399r
« on: November 30, 2016, 06:42:26 PM »
Hi kay_gsr13 ,
Would you be able to post the part of your PLC program with this timer in it and the logic that loads it to the array - I'm just wondering - since you mentioned the timer is in an array - whether converting to real may be causing the problem ?
If you are not able to post the code , perhaps you could add a rung and check that the conversion to a new real gives the value you are expecting . ( if the timer is in an array , then it takes 3 words )
Paul
Would you be able to post the part of your PLC program with this timer in it and the logic that loads it to the array - I'm just wondering - since you mentioned the timer is in an array - whether converting to real may be causing the problem ?
If you are not able to post the code , perhaps you could add a rung and check that the conversion to a new real gives the value you are expecting . ( if the timer is in an array , then it takes 3 words )
Paul
11
Support Questions / Re: AB CLX driver in Version 3.99c and later
« on: May 03, 2016, 05:39:31 PM »
Excellent !
12
Support Questions / Re: AB CLX driver in Version 3.99c and later
« on: May 03, 2016, 03:39:51 PM »
Hi Archie ,
If the problem with missing drivers is with VB2015 , are you using some code from 2015 to load the drivers to the toolbox ? At present I'm still using VB2010 and first noticed the problem with V399c using VB2010 .
Paul
If the problem with missing drivers is with VB2015 , are you using some code from 2015 to load the drivers to the toolbox ? At present I'm still using VB2010 and first noticed the problem with V399c using VB2010 .
Paul
13
Support Questions / Re: Numbering Screens
« on: April 09, 2016, 04:48:37 PM »
Thank you yet again Archie .
Paul
Paul
14
Support Questions / Re: Numbering Screens
« on: April 08, 2016, 06:23:17 PM »
Thank you Archie for the quick reply . How do I get The PLC to select a screen ? - I'm developing a help system for faults and would like bring up related text screens with detailed descriptions if the operator presses a "More Button "
Thanks , Paul
Thanks , Paul
15
Support Questions / Numbering Screens
« on: April 07, 2016, 03:13:57 PM »
I'm missing something . Is there a way of numbering screens so that the number can be sent to the PLC and also the PLC can call a screen by number ?
Paul
Paul