1
Support Questions / particle photon and advancedhmi
« on: May 25, 2016, 04:39:53 AM »
is there is a way to control particle photon with advancedhmi ?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Support Questions / Which of those HMI would works
« on: January 13, 2016, 05:26:09 PM »
I finished design my hmi and I wanna buy one Pc display so I can download it in to it which of these works
3
Support Questions / Re: Problem monitoring the out put
« on: January 12, 2016, 07:03:54 PM »
Let me make it more clear to u sir
I did traffic lights ladder logic by three timer
I wanna use the stack light In the Hmi to monitoring my ladder the DN bit of the timer turn the out put ON for the red and orang and green so wen the red turn on I want the stack light in the hmi turn on then orang then green on and on
So what should I put in the plcaddressvalue for the stack light to monitor my output ?
I did traffic lights ladder logic by three timer
I wanna use the stack light In the Hmi to monitoring my ladder the DN bit of the timer turn the out put ON for the red and orang and green so wen the red turn on I want the stack light in the hmi turn on then orang then green on and on
So what should I put in the plcaddressvalue for the stack light to monitor my output ?
4
Support Questions / Problem monitoring the out put
« on: January 12, 2016, 05:46:00 PM »
Hello
I have problem monitoring my out put wen its true it won't show in the hmi this out put is on
But if I turn it on from the hmi it show the pilot light on coz both the pilot light and the memontery button are the same address B3/0
But if I force the out put to on it won't show in the hmi unless I energize it from hmi
I have problem monitoring my out put wen its true it won't show in the hmi this out put is on
But if I turn it on from the hmi it show the pilot light on coz both the pilot light and the memontery button are the same address B3/0
But if I force the out put to on it won't show in the hmi unless I energize it from hmi
5
Support Questions / Re: I can't connect df1
« on: January 09, 2016, 10:57:28 PM »
I did and it's not working
I create rung with XIC address B3:0/0
And in the hmi memontery button with address b3/0 and still not able to control it
The rslinx Classic turned off from the task Manegar
The COM matches
And the Plc in run mode
Still am not able
I would be appreciate it for the help
Thanks
I create rung with XIC address B3:0/0
And in the hmi memontery button with address b3/0 and still not able to control it
The rslinx Classic turned off from the task Manegar
The COM matches
And the Plc in run mode
Still am not able
I would be appreciate it for the help
Thanks
6
Support Questions / I can't connect df1
« on: January 09, 2016, 04:52:30 PM »
Hello am using the df1 com and I did set the comport and close the rslinx
But still I can't communicate from the afvancedhmi memo try button to control my Plc
Plz I would appreciate any help
Thanks
But still I can't communicate from the afvancedhmi memo try button to control my Plc
Plz I would appreciate any help
Thanks
7
Support Questions / Re: Problem connecting AdvancedHMI to AB Micrologix 1200
« on: January 09, 2016, 04:32:10 PM »
Hello buddy did u figure it out
Am using DF1 and I did turn the rslinx off still not working ? Any luck
Am using DF1 and I did turn the rslinx off still not working ? Any luck
Pages: [1]