AdvancedHMI Software
General Category => Open Discussion => Topic started by: abdala on April 26, 2018, 02:53:18 PM
-
Why not use the protocol you CNET in PLC LS IN Korea FOR protocol MODBUS RTU
From my experience to the JET program protocol CNET
better than protocol MODBUS RTU
protocol MODBUS RTU BAD
protocol CNET GOOD
Please Add protocol CNET to AdvancedHMI
-
What brand PLC? Can you post a web site link?
-
XGB Series
(http://www.lsis.com/upload/product/A03002002.png)
http://www.lsis.com/support/download/
http://www.lsis.com/product/depth2.aspx?d1=CCC&d2=001&d3=002 (http://www.lsis.com/product/depth2.aspx?d1=CCC&d2=001&d3=002)
protocol MODBUS RTU bad link and protocol MODBUS tcp
protocol Cnet good and fnet
There is a link in the manual
in Korea
Widespread in Egypt In the country
-
You can not expect Archie to go about purchasing hardware to create a new driver.
If you or somebody from Egypt or Korea is willing to donate hardware then Archie would probably go about creating a new driver.
Do you know if there is possibly a simulator available?
-
I have created a new driver and work efficiently with the simulation program
XG5000
(http://c.up-00.com/2018/04/152489840706221.jpg)
These files are new driver
cnet
and
fenet
All I need to do is check code and make sure the code is working with high efficiency and I want to share it
(http://a.up-00.com/2018/04/152489824695351.jpg)
-
Simulation
http://www.j1lab.com/zb4/view.php?id=download&page=1&sn1=&divpage=1&sn=off&ss=on&sc=on&select_arrange=headnum&desc=asc&no=56 (http://www.j1lab.com/zb4/view.php?id=download&page=1&sn1=&divpage=1&sn=off&ss=on&sc=on&select_arrange=headnum&desc=asc&no=56)
-
(http://a.up-00.com/2018/04/152494829373961.jpg)
(http://c.up-00.com/2018/04/152494851091361.jpg)
Try and you'll see
-
If your drivers work as you suggest then keep them available here for other users.
Also, do provide any updates you might have in the future.
I don't think that Archie will include them in the project since then he would have to support them.
Currently, I am trying to use XG5000 program and its simulator, which seem to work as per attached picture.
How would I go about using your driver and a BasicLabel to read from/write to In_1?
The driver and the BasicLabel are already added to AHMI project.
What PLCAddressValue would I have to use?
-
abdala,
Would you mind to share your baraka_plc project and attach the zip file of your project's folder?
I would like to try it since it shows Network Configuration section which I can't get into my project.
It is probably related to a physical PLC which you might have but it wouldn't hurt for me to try it just to see what I get without having the PLC.
-
I have no objection
To run the project you must install this version
XG5000_V4.24_En(2018-03-19)_REL
If you want a full project you will pay for it
XGB Cnet USERS MANUAL V1.3.pdf
http://www.daviscontrols.com/synergydownload/LS_STORE/PLC/PLC%20Manuals/XGB%20Cnet%20USERS%20MANUAL%20V1.3.pdf (http://www.daviscontrols.com/synergydownload/LS_STORE/PLC/PLC%20Manuals/XGB%20Cnet%20USERS%20MANUAL%20V1.3.pdf)
the page 75
Chapter 7 XGT Dedicated Protocol
You have been raised the entire project
Please review the project and show errors
https://up.top4top.net/downloadf-851xw7eu1-7z.html (https://up.top4top.net/downloadf-851xw7eu1-7z.html)
-
Thank you abdala.
It is only the knowledge that I gain by testing all these and there is no other benefit to me.
The software you suggested, V4.24, seems to be better than the one I had (at least I can see the same screen as your pictures show).
From your project I did find out the correct address format, which was %DW or %MX or ..., and a page in the manual also reflected those W/X/L and other designations.
Currently, I am still not successful in getting the AHMI to connect to the XG simulator.
No Response from PLC is continuous error regardless of how I set the IP addresses in both the driver and XG software.
This all requires more time and research.
If I am to be successful in the future then I will post it up here.
-
thank you for your interest
You can see the results with the use of
Simulation
http://www.j1lab.com/zb4/view.php?id=download&page=1&sn1=&divpage=1&sn=off&ss=on&sc=on&select_arrange=headnum&desc=asc&no=56
(http://c.up-00.com/2018/04/152494851091361.jpg)
You can communicate with me through
TeamViewer
link to plc my
Or through Facebook
https://www.facebook.com/profile.php?id=100005696566177
Many programs are used
Web-N+2.3.0+Release+MultiLanguage(x86)